How to Use a Plumbing Snake
- by siteadmin
A plumbing snake is a tool that can be used to remove the blockage from your drains without chemicals. They are easy to use and can save you money in the long run.
To unclog a drain with a snake, insert it into the pipe and crank it until it reaches the clog. When you feel resistance, continue to turn it slowly.
Crank the Handle
A plumbing snake is a great tool for unclogging drains, but only if you know how to use it correctly. If you don't, it may do more harm than good.
The first step is to manually thread the auger head of your snake into a drain. This can be done either in the sink, or if you're unclogging a shower drain, in the tub drain.
Once you've physically inserted the tip of your snake into the pipe, loosen the thumbscrew. This will allow the cable to recede, letting you wind it back up through the pipe and remove the clog-causing sludge.
Once the cable is back up through the pipe, turn the handle of your snake two or three times to force it into the clog. Depending on the size and tightness of the blockage, this should break it up enough to disrupt the drain. This will also make it easier to remove the clog and sludge.
Twist the Wire
Twisting the wire of a plumbing snake allows the corkscrew auger head to break up soft blockages. It also attaches onto solid clogs to snag them and pull them out.
Using a plumbing snake is an inexpensive way to unclog sinks, showers, tubs, and toilets. However, it is important to know how to use it correctly so that you can avoid making a costly mess in the future.
Before you begin, be sure to choose a drain snake that is specifically made for the type of pipe in which you'll be working. If you use a snake that is too wide for your pipes, it could rip or tear the pipe when it breaks through the clog.
To begin, insert the cable into the drain and twist the handle clockwise. Extend the snake into the pipe a few inches at a time, gradually extending it until you reach the clog. Keep the handle as close to the pipe entrance as possible to apply the most force.
Feed the Wire into the Drain
A plumbing snake is a handy tool that can help you clear a drain clog. It works by pushing a wire through the drain to break up whatever material is causing the blockage.
Before you use a snake, remove the trap arm from your sink or tub to gain the best access possible. It can be very difficult to snake a clogged pipe if the trap arm is still attached.
Now that the trap is off, manually thread the auger head of your snake into the pipe. You may need to run cold water while you snake, since hot water can damage pipes.
Once the auger is in, crank the handle clockwise to rotate it toward the clog. If you feel resistance, push the cable forward a little more.
Once you hit the clog, keep turning the handle to push the corkscrew end of the cable through the clog. You can also push back on the wire a bit if you feel resistance when it gets to a tight corner in the pipe.
Remove the Wire
A plumbing snake is a long flexible tool that is used to unclog drains and pipes that are clogged. Its coiled wire is attached to a crank that allows you to move the hook throughout the pipe until it comes into contact with a clog.
A clog in the drain can be caused by small things like food, soap, and hair. These items can slow down the flow of water and cause a plumbing emergency, so knowing how to use a plumbing snake is important.
The first step in using a plumbing snake is to thread the head of the auger into the drain. You can usually do this with your hands, but you should have a bucket underneath the sink to catch any debris that may come out when you detach the P-trap under the drain.
7004 Colonial Ct, North Wales PA 19454
A plumbing snake is a tool that can be used to remove the blockage from your drains without chemicals. They are easy to use and can save you money in the long run. To unclog a drain with a snake, insert it into the pipe and crank it until it reaches the clog. When you…